Der neue Raspberry Pi 5 auf Lager ×

Arduino ProtoShield - Bare PCB

The SparkFun Arduino ProtoShield is a bare PCB with no attached or included parts that lets you customize your own Arduino shield using whatever circuit you can come up with! You will even be able to test your circuit or project to make sure everything is working the way it should! The SparkFun Arduino ProtoShield is based off the Arduino R3’s footprint that allows you to easily incorporate it with favorite Arduino-based device.

Now you don’t need to buy the whole ProtoShield kit if you just need a piece of prototyping board that will fit on top of your Arduino. You might want to grab a stackable header kit, though, which you can find in the related items below.


7,50 €
inkl. 20% USt. , zzgl. Versand
Nicht auf Lager
Beschreibung

The SparkFun Arduino ProtoShield is a bare PCB with no attached or included parts that lets you customize your own Arduino shield using whatever circuit you can come up with! You will even be able to test your circuit or project to make sure everything is working the way it should! The SparkFun Arduino ProtoShield is based off the Arduino R3’s footprint that allows you to easily incorporate it with favorite Arduino-based device.

Now you don’t need to buy the whole ProtoShield kit if you just need a piece of prototyping board that will fit on top of your Arduino. You might want to grab a stackable header kit, though, which you can find in the related items below.

One of our favorite features with this version of the Arduino ProtoShield is the solderable-like breadboard prototyping area! Half of this area was designed with a breadboard in mind. On the underside of the shield you will be able to see open jumper pads between each through hole to make a connection like a breadboard. Once you add a component, simply add a solder jumper between holes to make a connection. For those that prefer the standard prototyping pads, we left the other side (near the BlueSMiRF and Serial UART ports) as is.

We have also moved the prototype testing components (those used to make sure your circuit works effectively) off of the “mainland” of the shield and onto a ProtoSnap styled, removable PCB. On this test area you will find soldering areas for two 3mm LEDs (as well as pins to control and power them), two 330 Ohm resistors, a 10K Ohm resistor, and a pushbutton. These items you’ll need to purchase separately.

Features

  • Arduino R3 Footprint
  • Solderable-Like Breadboard
  • BlueSMiRF or Comparable 6-pin Pins
  • Detachable Test Area

Documents

Bewertungen

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufentscheidung:

Kunden kauften dazu folgende Artikel:
Arduino Stapelbarer Header Bausatz - R3
Arduino Stapelbarer Header Bausatz - R3
42 Auf Lager SKU: SPP11417
6 Pin Female Header 2.54mm (2 Stk)
> 50 lagernd SKU: SER00501
8 Pin Female Header 2.54mm
> 50 lagernd SKU: SER00005
Breadboard 400 Pins - 8.3 x 5.5 cm
Top bewertet
> 50 lagernd SKU: SER00419
Jumper Wire Female to Male 10Pin - 20cm
Top bewertet
> 50 lagernd SKU: SER00063
LED - Basic Green 5mm
LED - Basic Green 5mm
1 Auf Lager SKU: RS2286004
Screw Terminals 3.5mm Pitch (2-Pin)
42 Auf Lager SKU: SER00006
Schaltdiode 1N4001 - 50V - 1A
Schaltdiode 1N4001 - 50V - 1A
> 50 lagernd SKU: RS7512718
LED - Basic Yellow 5mm
LED - Basic Yellow 5mm
> 50 lagernd SKU: RS2286010
Break Away Male Headers - Straight 40Pin - Black
Ausverkauft
Nicht auf Lager SKU: SPP00116
LED - Basic Red 5mm
LED - Basic Red 5mm
Ausverkauft
Nicht auf Lager SKU: SER01153
Kondensator 10nF 50V - 103
Ausverkauft
Nicht auf Lager SKU: SER00530
Loading ...
kein Bild
Artikelnummer:
ab *
/