Der neue Raspberry Pi 5 auf Lager ×

BH1745 Luminance and Colour Sensor Breakout

A really sophisticated and accurate colour and luminance sensor breakout that's Raspberry Pi and Arduino compatible. As well as detecting RGB colour and light level, it has added bells and whistles like 50/60Hz light noise rejection, a wide detection range, and two illumination LEDs.

16,00 €
inkl. 20% USt. , zzgl. Versand
10 Auf Lager
Lieferdatum: 02.04.2024 - 04.04.2024 (Österreich - Ausland abweichend)
Beschreibung

A really sophisticated and accurate colour and luminance sensor breakout that's Raspberry Pi and Arduino compatible. As well as detecting RGB colour and light level, it has added bells and whistles like 50/60Hz light noise rejection, a wide detection range, and two illumination LEDs.

This type of sensor is the same as you'd find in phones, tablets, and laptops where they're used to detect ambient light temperature and adjust the colour temperature of the display accordingly. The BH1745 Luminance and Colour Sensor Breakout has an I2C interface and is 3.3V or 5V compatible. Like our other Semaf Electronics breakouts, we've designed it so that you can solder a piece of right-angle header onto it and then pop it straight onto the bottom left 5 pins on your Raspberry Pi's GPIO header (pins 1, 3, 5, 6, 9). It's also compatible with our fancy new Breakout Garden, where using breakouts is as easy just popping it into one of the six slots and starting to grow your project, create, and code.

Features

  • BH1745 Luminance and Colour Sensor Breakout
  • Two white illumination LEDs
  • Red, green, blue, and luminance measurements
  • 0.005 to 40,000 lx detection range
  • 50/60Hz light noise rejection
  • IR cut filter
  • 16 bit data output
  • 3.3V or 5V compatible
  • I2C interface, with address select via ADDR cuttable trace (0x38 or 0x39)
  • Reverse polarity protection
  • Raspberry Pi-compatible pinout (pins 1, 3, 5, 7, 9)
  • Compatible with Raspberry Pi 3B+, 3, 2, B+, A+, Zero, and Zero W
  • Python library
  • Datasheet

Kit includes

  • BH1745 Luminance and Colour Sensor Breakout
  • 1x5 male header
  • 1x5 female right angle header

Software

We've put together a Python library that you can use to read data from your BH1745 Luminance and Colour Sensor Breakout, and an easy one-line installer to install everything.

Our software does not support Raspbian Wheezy.

Notes

  • The trace between the solder pads (marked ADDR) can be cut (carefully with a craft knife) to change the I2C address from the default of 0x38 to 0x39, meaning that you can use up to two sensors on the same Raspberry Pi or Arduino. If cut, the pads can be bridged again by soldering to reset the address to 0x38.

Bewertungen

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufentscheidung:

zubehör
Breakout Garden HAT
Breakout Garden HAT
2 Auf Lager SKU: PIM00377
Kunden kauften dazu folgende Artikel:
Breakout Garden HAT
Breakout Garden HAT
2 Auf Lager SKU: PIM00377
Flex Cable for Raspberry Pi Camera and LCD Display - 45cm
> 50 lagernd SKU: SER00746
BME680 Breakout - Air Quality - Temperature - Pressure -...
BME680 Breakout - Air Quality - Temperature - Pressure -...
10 Auf Lager SKU: PIM00357
Raspberry Pi Zero WH
Raspberry Pi Zero WH
> 50 lagernd SKU: SER00750-WH
Offizielles Raspberry Pi Zero W Gehäuse
Offizielles Raspberry Pi Zero W Gehäuse
Top bewertet
> 50 lagernd SKU: RPI00001
Flex Cable for Raspberry Pi Camera and LCD Display - 60cm
> 50 lagernd SKU: SER00747
Break Away 2x20 Pin Strip Dual Male Header
8 stück Auf Lager SKU: SER00752
nRF24l01+ 2.4G Wireless Module - 2 Stück
nRF24l01+ 2.4G Wireless Module - 2 Stück
> 50 lagernd SKU: SER00140
BME280 I2C Temperature Humidity Pressure Sensor
BME280 I2C Temperature Humidity Pressure Sensor
1 Auf Lager SKU: SER01526
Raspberry Pi Zero W
Raspberry Pi Zero W
ab 18,00 € *
Nicht auf Lager SKU: SER00750-OB
NodeMCU ESP32 Development Board
NodeMCU ESP32 Development Board
Ausverkauft
Nicht auf Lager SKU: SER00749
9DOF Axis IMU MPU9250 and BMP280 Atmospheric Sensor
9DOF Axis IMU MPU9250 and BMP280 Atmospheric Sensor
Ausverkauft
Nicht auf Lager SKU: SER00706
Load Cell Amplifier - HX711
Load Cell Amplifier - HX711
Ausverkauft
Nicht auf Lager SKU: SER00704
DHT22 temperature-humidity sensor + extras
Ausverkauft
Nicht auf Lager SKU: SER00635
Loading ...
kein Bild
Artikelnummer:
ab *
/