DS3231 is a low-cost, extremely accurate I2C real-time clock (RTC), with an integrated temperature-compensated crystal oscillator (TCXO) and crystal. Compared to the DS1302 solution, the DS3231 has many advantages, it function with a VCC ranging from 2.3V to 5.5V and has a battery backup. Unlike the DS1307, the DS3231 also has an integrated crystal (so no external crystal required), temperature sensor, 2 programmable time-of-day alarms, a 32.768 kHz output pin to ensure higher accuracy.
Besides, there is also a EEPROM AT24C32 to supply you 32K EEPROM to store your data, it is the best choice for your application that needs recoding time, a built battery holder make this module suitable. It is a good substitution for the data logging shield, with even higher time precision.
Size: 38mm (length) * 22mm (W) * 14mm (height)
Operating voltage :3.3 - 5 .5 V
Clock chip: high-precision clock chip DS3231
Clock Accuracy :0-40 ? range, the accuracy 2ppm, the error was about 1 minute
Calendar alarm clock with two
Programmable square-wave output
Real time clock generator seconds, minutes, hours, day, date, month and year timing and provide valid until the year 2100 leap year compensation
Chip temperature sensor comes with an accuracy of 3 ?
Memory chips: AT24C32 (storage capacity 32K)
IIC bus interface, the maximum transmission speed of 400KHz (working voltage of 5V)
Can be cascaded with other IIC device, 24C32 addresses can be shorted A0/A1/A2 modify default address is 0x57
Miniature Single Pull Single Throw switches. These are high quality Omron type B3F momentary on switches. This switch has a very large 5mm tall button. Perfect as an embedded switch behind an enclosure wall. Rated up to 50mA.
BME280 is a Breakout Board featuring a Bosch Sensortec ME280 Temperature, Humidity amp; Pressure Sensor. The board has selectable I2C address jumper (solder link GS2), I2C pull-up resistors, 7 pin header 2.54mm, and two mounting holes 3.5mm.
Many current measuring devices are only good for low side measuring and monitoring. This means that unless you want to get a battery involved, you have to place the measurement resistor between the target ground and true ground. Doing this can cause problems with circuits since electronics tend to not like it when the ground references change and move...
If you\'ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level...
Single row of 30-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers.
This 1.3"OLED display module is made of 128x64 individual write OLED pixels, It uses I2C to communicate with microcontroller such as Arduino, with the given library, it would be easy to integrate the OLED display module into your project.
This 47 x 35mm (1.84 x 1.37") breadboard has 17 rows of tie points, enough for up to two 14 or 16 pin DIP integrated circuits (ICs). The board features an adhesive backing and is Blue color. Add some color to your next project!
Single row of 40-holes, female header. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away male headers.