Der neue Raspberry Pi 5 auf Lager ×

MPR121 Capacitive Touch Sensor Breakout Board

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touch pads.
The MPR121 has support for only I2C, which can be implemented with nearly any microcontroller. You can select one of 4 addresses with the ADDR pin, for a total of 48 capacitive touch pads on one I2C 2-wire bus. Using this chip is a lot easier than doing the capacitive sensing with analog inputs: it handles all the filtering for you and can be configured for more/less sensitivity.

3,00 €
inkl. 20% USt. , zzgl. Versand
Nicht auf Lager
Beschreibung

Add lots of touch sensors to your next microcontroller project with this easy-to-use 12-channel capacitive touch sensor breakout board, starring the MPR121. This chip can handle up to 12 individual touch pads.

The MPR121 has support for only I2C, which can be implemented with nearly any microcontroller. You can select one of 4 addresses with the ADDR pin, for a total of 48 capacitive touch pads on one I2C 2-wire bus. Using this chip is a lot easier than doing the capacitive sensing with analog inputs: it handles all the filtering for you and can be configured for more/less sensitivity.

This sensor comes as a tiny hard-to-solder chip so we put it onto a breakout board for you. Since it's a 3V-only chip, we added a 3V regulator and I2C level shifting so its safe to use with any 3V or 5V microcontroller/processor like Arduino. We even added an LED onto the IRQ line so it will blink when touches are detected, making debugging by sight a bit easier on you. Comes with a fully assembled board, and a stick of 0.1" header so you can plug it into a breadboard. For contacts, we suggest using copper foil or pyralux, then solder a wire that connects from the foil pad to the breakout.

Getting started is a breeze with our Arduino library and tutorial. You'll be up and running in a few minutes, and if you are using another microcontroller, its easy to port our code.

Uses I2C 7-bit address 0x5A (can be set to 0x5B, 0x5C or 0x5D)

Of course, we wouldn't leave you with a datasheet and a "good luck!" - we wrote a detailed tutorial showing how to wire up the sensor, use it with an Arduino and example code that gets the sensor logging data and detecting your touch!

Datasheet

Bewertungen

Geben Sie die erste Bewertung für diesen Artikel ab und helfen Sie Anderen bei der Kaufentscheidung:

Kunden kauften dazu folgende Artikel:
Krokodil Klemmen
5 Auf Lager SKU: SER00015
Widerstand 220R 5% 0,25W
> 50 lagernd SKU: RS7077612
20 Pin Female Header Extra Tall 2.54mm
> 50 lagernd SKU: SER01309
Jumper Wire Female to Male 10Pin - 20cm
Top bewertet
> 50 lagernd SKU: SER00063
Jumper Wire Male to Male 10 Pin - 20cm
> 50 lagernd SKU: SER00062
Fotowiderstand - Photoresistor 10k
> 50 lagernd SKU: SPS09088
Widerstand 1M 5% 0,25W
10 Auf Lager SKU: RS7077903
Widerstand 150R 5% 0,25W
> 50 lagernd SKU: RS7077603
Heatsink Aluminium Set for Raspberry Pi
Heatsink Aluminium Set for Raspberry Pi
Ausverkauft
Nicht auf Lager SKU: SER90010
Rotary Potentiometer - 10k Ohm, Linear
Rotary Potentiometer - 10k Ohm, Linear
Ausverkauft
Nicht auf Lager SKU: SPC09939
HC-SR04 Ultrasonic Sensor
HC-SR04 Ultrasonic Sensor
Ausverkauft
Nicht auf Lager SKU: SER00458
Vibration Motor
Ausverkauft
Nicht auf Lager SKU: SPR08449
Loading ...
kein Bild
Artikelnummer:
ab *
/