Angebote ×

DRV8833 DC/Stepper Motor Driver Breakout Board

Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver. Like that chip, you get 2 full H-bridges, but this chip is better for low voltage uses (can run from 2.7V up to 10.8V motor power) and has built in current limiting capability. We set it up for 1A current limiting so you don't get more than 2A per chip, but you can also disable the current limiting, or change it to a different limit!

6,00 €
incl. 20% VAT , plus shipping costs
Out of stock
Description

Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver. Like that chip, you get 2 full H-bridges, but this chip is better for low voltage uses (can run from 2.7V up to 10.8V motor power) and has built in current limiting capability. We set it up for 1A current limiting so you don't get more than 2A per chip, but you can also disable the current limiting, or change it to a different limit!

We solder on DRV8833 onto a breakout board for you here, with a polarity protection FET on the motor voltage input. Each breakout chip contains two full H-bridges (four half H-bridges). That means you can drive two DC motors bi-directionally, or one stepper motor. Just make sure they're good for about 1.2 Amp or less of current, since that's the limit of this chip. They do handle a peak of 2A but that's just for a short amount of time, if you turn off the current limiting we set. What we like most about this particular driver is that it comes with built in kick-back diodes internally so you dont have to worry about the inductive kick damaging your project or driver! You also don't have to worry as much about burning out the chip with overdriving since there is current limiting.

There's two digital inputs per H-bridge (one for each half of the bridge), you can PWM one of the inputs to control motor speed. Runs at 2.7V-10.8V logic/motor power. The motor voltage is the same as the logic voltage, but logic voltage from 2.7V or greater will work so no need to worry if you are powering the motors from 9V and using 3.3V logic. For higher voltages, check out the TB6612. For much higher voltages and currents check out the DRV8871!

Comes as one assembled and tested breakout plus a small strip of header. You'll need to do some light soldering to attach the header onto the breakout PCB. Arduino, motors, and power supply not included.

Note: The terminal block included with your product may be blue or black.

Technical Details

Reviews

Write the first review for this item and help others make a purchase decision!:

Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)
Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)
Out of stock
Out of stock SKU: SPR13656
Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
Out of stock
Out of stock SKU: SPR10848
Stepper Motor with Cable
Stepper Motor with Cable
Out of stock
Out of stock SKU: SPR09238
Others also bought:
USB-C OTG Mini Adapter
In stock
10 in stock SKU: SER01254
LED - RGB Clear Common Anode
LED - RGB Clear Common Anode
In stock
> 50 lagernd SKU: SPC00105
Male DC Power adapter - 2.1mm jack to screw terminal block
Male DC Power adapter - 2.1mm jack to screw terminal block
In stock
> 50 lagernd SKU: SER00018
Female DC Power adapter - 2.1mm jack to screw terminal block
Female DC Power adapter - 2.1mm jack to screw terminal block
In stock
> 50 lagernd SKU: SER00017
LED - Infrared 940nm
In stock
> 50 lagernd SKU: SPC09469
P-Channel MOSFET 20V 24A - low Vgs(th) - NDP6020P
P-Channel MOSFET 20V 24A - low Vgs(th) - NDP6020P
Out of stock
Out of stock SKU: SER00144
Temperature Sensor - Waterproof (DS18B20) - 1 meter
Temperature Sensor - Waterproof (DS18B20) - 1 meter
Out of stock
Out of stock SKU: SER00010
NodeMCU ESP32 Development Board
NodeMCU ESP32 Development Board
Out of stock
Out of stock SKU: SER00749
DC-DC Step Down Converter (4~28V to 5V 3A)
Out of stock
Out of stock SKU: SER01066
Mini Stepper Motor Kit - ULN2003A with 28BYJ-48
Mini Stepper Motor Kit - ULN2003A with 28BYJ-48
Out of stock
Out of stock SKU: SER00167
Sparkfun EasyDriver Stepper Motor Driver
Sparkfun EasyDriver Stepper Motor Driver
Out of stock
Out of stock SKU: SPR12779
28BYJ-48 High Quality Stepper Motor 5V
28BYJ-48 High Quality Stepper Motor 5V
Out of stock
Out of stock SKU: SER00020
Break Away Male Headers - Straight 40Pin - Black
Out of stock
Out of stock SKU: SPP00116
Loading ...
kein Bild
id:
from *
/
In den Warenkorb
goto offer