Angebote ×

Ethernet Shield with Wiznet W5100 Ethernet Chip

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. it'supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

18,95 €
incl. 20% VAT , plus shipping costs
Out of stock
Description

The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100 ethernet chip. The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. it'supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.

The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board.

The Ethernet Shield has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.

There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard microSD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the shield contained a full-size SD card slot; this is not supported.

The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.

The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:

  • IEEE802.3af compliant
  • Low output ripple and noise (100mVpp)
  • Input voltage range 36V to 57V
  • Overload and short-circuit protection
  • 9V Output
  • High efficiency DC/DC converter: typ 75% @ 50% load
  • 1500V isolation (input to output)

NB: the Power over Ethernet module is proprietary hardware not made by Arduino, it is a third party accessory. For more information, see the datasheet

The shield does not come with the PoE module built in, it is a separate component that must be added on.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins cannot be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, hoWe'ver, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

The shield provides a standard RJ45 ethernet jack.

The reset button on the shield resets both the W5100 and the Arduino board.

The shield contains a number of informational LEDs:

  • PWR: indicates that the board and shield are powered
  • LINK: indicates the presence of a network link and flashes when the shield transmits or receives data
  • FULLD: indicates that the network connection is full duplex
  • 100M: indicates the presence of a 100 Mb/s network connection (as opposed to 10 Mb/s)
  • RX: flashes when the shield receives data
  • TX: flashes when the shield sends data
  • COLL: flashes when network collisions are detected

The solder jumper marked "INT" can be connected to allow the Arduino board to receive interrupt-driven notification of events from the W5100, but this is not supported by the Ethernet library. The jumper connects the INT pin of the W5100 to digital pin 2 of the Arduino.

Reviews (1)

5/5
(1)

4 Stars
3 Stars
2 Stars
1 Star

Share your experiences with other customers!

Damit beginnt das Internet of Things
5 from 5

Funktioniert tadellos. Man muss nur darauf achten, dass man den Arduino mit genügend Spannung versorgt. Ich hatte nur 6,5V angelegt und da machte das Shield keinen mux.
Mit mehr hat es dann problemlos funktioniert.
Geht alles.

Hannes M., 04.01.2016
Others also bought:
Raspberry Pi T-Cobbler GPIO 40 Pin for Breadboard
Raspberry Pi T-Cobbler GPIO 40 Pin for Breadboard
In stock
34 Auf Lager SKU: SER00532
1 Pin Dupont Cable Housing
In stock
> 50 lagernd SKU: SER00079
Breadboard 400 Pins - 8.3 x 5.5 cm
Top rated
> 50 lagernd SKU: SER00419
Jumper Wire Female to Male 10Pin - 20cm
Top rated
> 50 lagernd SKU: SER00063
Breadboard 830 Pins - 16.5 x 5.4 cm
Breadboard 830 Pins - 16.5 x 5.4 cm
Top rated
22 in stock SKU: SER00075
DIP 28 Pin Socket Solder Tail
In stock
> 50 lagernd SKU: SER00050
Triple Axis Accelerometer and Gyro Breakout - MPU6050
Out of stock
Out of stock SKU: SER00126
Female Crimp pins for Dupont Connectors
Female Crimp pins for Dupont Connectors
Out of stock
Out of stock SKU: SER00084
Proto Screw Shield
Proto Screw Shield
Out of stock
Out of stock SKU: SPD09729
NodeMCU v2 - ESP8266
NodeMCU v2 - ESP8266
Out of stock
Out of stock SKU: SER00424
Loading ...
kein Bild
id:
from *
/