Angebote ×

Adafruit Motor-Stepper-Servo Shield for Arduino v2 Kit

The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements:

30,00 €
incl. 20% VAT , plus shipping costs
Out of stock
Description

The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper motors, but added many improvements:

Instead of a L293D darlington driver, we now have the TB6612 MOSFET driver: with 1.2A per channel and 3A peak current capability. It also has much lower voltage drops across the motor so you get more torque out of your batteries, and there are built-in flyback diodes as well.

Instead of using a latch and the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard. This chip handles all the motor and speed controls over I2C. Only two pins (SDA amp; SCL) are required to drive the multiple motors, and since it's I2C you can also connect any other I2C devices or shields to the same pins. This also makes it drop-in compatible with any Arduino, such as the Uno, Due, Leonardo and Mega R3.

Completely stackable design: 5 address-select pins means up to 32 stackable shields: that's 64 steppers or 128 DC motors! What on earth could you do with that many steppers? I have no idea but if you come up with something send us a photo because that would be a pretty glorious project.

Lots of other little improvements such as a polarity protection FET on the power pins and a bit of prototyping area. And the shield is assembled and tested here at Adafruit'so all you have to do is solder on straight or stacking headers and the terminal blocks.

Specifications

  • 2 connections for 5V 'hobby' servos connected to the Arduino's high-resolution dedicated timer - no jitter!
  • 4 H-Bridges: TB6612 chipset provides 1.2A per bridge (3A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 13.5VDC.
  • Up to 4 bi-directional DC motors with individual 8-bit'speed selection (so, about 0.5% resolution)
  • Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil, interleaved or micro-stepping
  • Motors automatically disabled on power-up
  • Big terminal block connectors to easily hook up wires (18-26AWG) and power
  • Arduino reset button brought up top
  • Polarity protected 2-pin terminal block and jumper to connect external power, for separate logic/motor supplies
  • Tested compatible with Arduino UNO, Leonardo, ADK/Mega R3, Due, Diecimila amp; Duemilanove. Works with Mega/ADK R2 and earlier with 2 wire jumpers.
  • Download the easy-to-use Arduino software library, check out the examples and you're ready to go!

Comes with an assembled amp; tested shield, terminal block, plain header, jumper. Some soldering is required to assemble the headers on. Stacking headers not included, but we sell them in the shop so if you want to stack shields, please pick them up at the same time. Arduino and motors are not included but we have lots of motors in the shop and all our hobby servos, DC motors, and stepper motors work great. New! As of 3/21/2014 we are shipping motor shields with the terminal blocks, and power jumper pre-soldered on. You'll still need to do a little soldering to put on the shield-headers (or stacking headers) but it'should be even easier and faster to get started!

Details:

  • Dimensions, assembled: 70mm x 55mm x 10mm 2.7"x2.1"x0.4"
  • This board/chip uses I2C 7-bit addresses between 0x60-0x80, selectable with jumpers.

Reviews

Write the first review for this item and help others make a purchase decision!:

Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)
Stepper Motor - 125 oz.in (200 steps/rev, 600mm Wire)
Out of stock
Out of stock SKU: SPR13656
Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
Stepper Motor - 29 oz.in (200 steps/rev, Threaded Shaft)
Out of stock
Out of stock SKU: SPR10848
Stepper Motor with Cable
Stepper Motor with Cable
Out of stock
Out of stock SKU: SPR09238
Others also bought:
LCD 20x4 i2c Modul
LCD 20x4 i2c Modul
Top rated
2 in stock SKU: SER00014
Male Crimp pins for Dupont Connectors
Male Crimp pins for Dupont Connectors
Top rated
> 50 lagernd SKU: SER00111
4 Pin Dupont Cable Housing
In stock
> 50 lagernd SKU: SER00082
Female DC Power adapter - 2.1mm jack to screw terminal block
Female DC Power adapter - 2.1mm jack to screw terminal block
In stock
> 50 lagernd SKU: SER00017
Jumper Wire Female to Male 10Pin - 20cm
Top rated
> 50 lagernd SKU: SER00063
Stepper Motor with Cable
Stepper Motor with Cable
Out of stock
Out of stock SKU: SPR09238
Female Crimp pins for Dupont Connectors
Female Crimp pins for Dupont Connectors
Out of stock
Out of stock SKU: SER00084
28BYJ-48 High Quality Stepper Motor 5V
28BYJ-48 High Quality Stepper Motor 5V
Out of stock
Out of stock SKU: SER00020
2 Channels 5V Relay Module
Out of stock
Out of stock SKU: SER00456
Jumper Wire Female to Female 10Pin - 20cm
Out of stock
Out of stock SKU: SER00110
5 Pin Dupont Cable Housing
Out of stock
Out of stock SKU: SER00083
3 Pin Dupont Cable Housing
Out of stock
Out of stock SKU: SER00081
Loading ...
kein Bild
id:
from *
/