The PowerCell board is a single cell LiPo boost converter (to 3.3V and 5V) and micro-USB charger in one. The board comes with a JST connector for a single cell LiPo battery, a micro-USB connector for the 5V charge input, and selectable 3.3V and 5V output pins (labeled 'out'). There are also two charge pins broken out (labeled 'charge'), so you can use another 5V power source to charge the batteries, if you don't have a micro-USB cable.
We've also broken out the power-save and enable pins, so that you can have full control of the switching regulator. Keep in mind, if you keep your battery connected to the Powercell, it is recommended that you disable the switching regulator (pull EN low) in order to prevent the battery from discharging and reaching the under voltage cutoff on the battery itself. There is also an under-voltage lockout on the Powercell board which is tied to a solder jumper so that you can disable it if you like.
The micro-USB charger uses theMCP73831 and allows you to charge 3.7V LiPo cells at a rate of 100mA max. If you want to charge at a faster rate, you will need to connect a separate power supply to the pins labeled '5V' and 'GND' under the label 'charge'.
The boost converter is based on the TPS61200 from TI and has solder jumper selectable 5V and 3.3V output, and an under voltage protection of 2.6V (which can be disabled via solder jumper on the back of the PCB).
This board does not have reverse polarity protection, so please be sure to recognize the polarity of your connections!
1.03 x 0.95"
MCP73831 Single Cell LiPo charger at 500mA
TPS61200 Boost Converter
Selectable output voltage 3.3 or 5V
5V @ 600mA max
3.3V @ 200mA max
Undervoltage lock out at 2.6V (with disable jumper)
This is a breakout board for the Bosch BMP180 high-precision, low-power digital barometer. The BMP180 offers a pressure measuring range of 300 to 1100 hPa with an accuracy down to 0.02 hPa in advanced resolution mode. it\'s based on piezo-resistive technology for high accuracy, ruggedness and long term stability. These come factory-calibrated, with the...
This is a cute half size breadboard which has 400 tie-points, is great for small projects. it\'s 2.2" x 3.4" (5.5cm x 8.2cm) with a standard double-strip (300pts) in the middle and two power rails (100pts) on both sides. You can pull the power rails off easily to make the breadboard as thin as 1.4" (3.5cm) and stick it onto your Raspberry Pi. You...
Is there anything an Arduino can\'t do? Well, for one, most of them can\'t be powered directly from a 3.7V LiPo battery; much less charge and monitor that battery. The SparkFun LiPower Shield takes care of this by combining the functionality of two of our favorite battery power boards: the Power Cell and the Fuel Gauge.
This is a Arduino compatible PS2 Joystick Module for Robot Projects. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. This joystick module can be easily connect to Arduino by normal IO Expansion Shield with supplied cables.
No soldering required, Reusable...
These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (1 8-pin, 1 10-pin and 2 6-pin), enough to connect a shield to an Arduino board. These are the same headers we use in our...
This is a row of 40 break away headers spaced 0.1" apart with long pins on both sides. This header is especially useful when you need to connect a PCB to a solderless breadboard. Each header can be broken apart to your preference to fit custom PCBs or general custom headers.
If you\'ve ever tried to connect a 3.3V device to a 5V system, you know what a challenge it can be. The SparkFun bi-directional logic level converter is a small device that safely steps down 5V signals to 3.3V AND steps up 3.3V to 5V at the same time. This level converter also works with 2.8V and 1.8V devices. What really separates this Logic level...
Die Transponderkarte EM 4100 ist nur für den reinen Lesebetrieb geeignet (read only) und verfügt über eine werksseitige 8 Byte Seriennummer (einmalige UID). Daher ist das Einsatzgebiet recht begrenzt und beschrönkt sich meist auf die Bereiche der Zutrit\'skontrolle, Zeiterfassung und verschiedene industrielle Anwendungen.
Single row of 30-holes, female header with swiss round machined pins. These units have very high quality round pins to accept and retain machine pin headers much better. Can be cut to size with a pair of wire-cutters. Standard .1" spacing. We use them extensively in the Olimex development boards. They mate very well with break away headers.
7 auf Lager
Du erhälst eine Email benachrichtigung wenn das Artikel wieder auf Lager ist