This is gear grinding wire stripper / line clamp / wire cutter / plier. It is the simplest and fastest way to strip plastic or rubber insulation of single, multiple cables and wires. You just need to insert a wire into the jaws and squeeze the handles, now you're finished. The stripping diameter 0.6 - 2.5mm or 10 - 22 AWG.
Multi-use: It can be used as a wire cutter or plier, place the wire between cutter blades, close the handles fully and the wire was cut off, perfect for copper and aluminum wires, and you can use it to pull out nails too. With a lock to ensure your safety and high elasticity of the spring. No damaging to the conductor core, long lifetime, easy to carry......It is perfect for you!
Model : JAKEMY JM - CT4 - 12
Material : Metal, Plastic
Optional Color : Assorted Colors
Product size (L x W x H) : 18 x 6 x 1.3 cm / 7.07 x 2.36 x 0.51 inches
Package size (L x W x H) : 20 x 8 x 4 cm / 7.86 x 3.14 x 1.57 inches
Package Contents: 1 x JAKEMY JM - CT4 - 12 Wire Cutter Stripper Clamp 7.0 inch Hardware Tool
This is a simple-to-use Carbon Monoxide (CO) sensor, suitable for sensing CO concentrations in the air. The MQ-7 can detect CO-gas concentrations anywhere from 20 to 2000ppm.
This sensor has a high sensitivity and fast response time. The sensor\'s output is an analog resistance. The drive circuit is very simple; all you need to do is power the heater...
module is an easy to use Bluetooth SPP (Serial Port Protocol) module, designed for
transparent wireless serial connection setup.
Serial port Bluetooth module is fully qualified Bluetooth V2.0+EDR (Enhanced Data Rate) 3Mbps
Modulation with complete 2.4GHz radio transceiver and baseband.
A Feather board without ambition is a Feather board without FeatherWings! This is the Latching Mini Relay FeatherWing . It gives you power to control, and control over power. Put simply, you can now turn on and off lamps, fans, solenoids, and other small appliances that run on up to 250VAC or DC power using any Feather board.
A Feather board without ambition is a Feather board without FeatherWings!
This is the FeatherWing Proto - a prototyping add-on for all Feather boards.
This has a duplicate breakout for each pin on a Feather, as well as a bunch of plain grid proto holes. For GND and 3.3V, we give you a strip of connected pads. There\'s plenty of room for buttons ,...
This is the Teensy Audio board add-on for the Teensy 3.0 and 3.1 development boards. This audio board provides you with an easy-to-use tool to add high quality 16 bit, 44.1 kHz sample rate audio to your Teensy project. With the audio library provided in the Documents section below you will be able to use both the input and output simultaneously in order...
We\'ve created a brand new edition of the full-color SIK manual! Updated graphics, code revisions and in-depth instruction have been added to make learning basic electronics even easier! Make your way through the example circuits and you\'ll learn all about:
This breakout board is the ultimate companion for the VLSI VS1053B DSP codec chip. The VS1053 can decode a wide variety of audio formats such as MP3, AAC, Ogg Vorbis, WMA, MIDI, FLAC, WAV (PCM and ADPCM). It can also be used to record audio in both PCM (WAV) and compressed Ogg Vorbis. You can do all sorts of stuff with the audio as well such as adjusting...
The MG90 is a nice small RC servo ideal for projects where size and weight are important. RC servos are hobbyist remote control servos typically used in radio-controlled models, where they provide actuation for various mechanical systems such as the steering of a car, the flaps on a plane, or the rudder of a boat. These servos are not industrial grade and...