The Digispark is an Attiny85 based microcontroller development board similar to the Arduino line, only cheaper, smaller, and a bit less powerful. With a whole host of shields to extend its functionality and the ability to use the familiar Arduino IDE the Digispark is a great way to jump into electronics, or perfect for when an Arduino is too big or too much.
Support for the Arduino IDE 1.0+ (OSX/Win/Linux)
Power via USB or External Source - 5v or 7-35v (12v or less recommended, automatic selection)
On-board 500ma 5V Regulator
6 I/O Pins (2 are used for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB)
You\'ve got the wrong USB cable. It doesn\'t matter which one you have, it\'s the wrong one. But what if you could have the right one? What if you could have the right one every time? Enter: The Cerberus.
This is the kind of seat-of-the-pants engineering genius that you only find in hackspaces, garden sheds or Shenzhen.
It\'s not for the faint-of-heart, it\'s not particularly spec-friendly, but it is useful and cool for Pi Zero hackers!
By popular demand, we now have a handy extension cord for all of our JST-terminated battery packs (such as our LiIon/LiPoly and 3xAAA holders). One end has a JST-PH socket, and the other end has a matching plug. Between the two, 500mm of color coded wire. Handy for wearable projects where you may want the battery pack far from your Flora but...
The original Adafruit Motorshield kit is one of our most beloved kits, which is why we decided to make something even better. We have upgraded the shield kit to make the bestest, easiest way to drive DC and Stepper motors. This shield will make quick work of your next robotics project! We kept the ability to drive up to 4 DC motors or 2 stepper...
This is the SparkFun USB to Serial Breakout for the FT232RL, a small board with a built in USB to serial UART interface. This little breakout is built around the FT232RL IC from FTDI, with an internal oscillator, EEPROM, and a 28-pin SSOP package this is a serious little chip.
Introducing the WiPy 2.0. The tiny Micro Python enabled WiFi & Bluetooth IoT development platform. With a 1KM WiFi range, state of the art Espressif ESP32 chipset and dual processor, the WiPy is all about taking the Internet of Things to the next level. Create and connect your things everywhere. Fast.
These DC powered heating pads are perfect for near-body heating applications. They get warm to the touch but not too hot. Simply apply 5VDC to the wire leads and within minutes, the pad will begin to warm up.
These headers are made to work with the Arduino Uno R3, Leonardo and new Arduino boards going forward. They are the perfect height for clearing the USB-B connector and great for stacking multiple shields. This kit includes 4 headers (1 8-pin, 1 10-pin and 2 6-pin), enough to connect a shield to an Arduino board. These are the same headers we use in our...
The non-contact infrared thermometer (MLX90614ESF) for use with Arduino, or any microcontroller that can communicate with it through it\'s I2C interface.This sensor comes with a breakout board with all of the components needed for operation and two types of pins. They are unsoldered.
Das Arduino Uno R3 ist ein Mikrocontroller Board basierend auf einem ATmega328. Es hat 14 digitale Ein- / Ausg?nge (6 davon k?nnen als PWM Kan?le genutzt werden), 6 analoge Eing?nge, ein 16 MHz Quartz, USB Schnittstelle, einen 6 poligen ISP Anschluss und einen Reset Taster. Es enth?lt alles n?tige zum Start; man kann es einfach mit einem USB Kabel mit dem...
A central mounting hole on the front side to allow for three point mounting. This is much easier for bed leveling in comparison to 4 point mounting. First level the side with two holes and fix in place, then level the side with one hole. A glass plate is highly recommended to provide a truly flat surface and rigidity
The pads to solder onto have been...